你知道濟南輕型鋼結構工程中主要的檢測內容包含什么嗎？多了解一些相關內容就能讓您在后期的使用中順利進行施工，下面小編為您講解。

Do you know what the main inspection contents of Jinan light steel structure project include? Learn more about the relevant content to enable you to carry out the construction smoothly in the later use. The following sections will explain for you.

構件尺寸及平整度的檢測每個尺寸在構件的3個部位量測，取3處的平均值作為該尺寸的代表值。鋼構件的尺寸偏差應以設計圖紙規定的尺寸為基準計算尺寸偏差；

Inspection of component size and flatness Each size is measured at 3 parts of the component, and the average value of 3 parts is taken as the representative value of this size. The size deviation of steel members shall be calculated based on the size specified in the design drawings;

偏差的允許值應符合其產品標準的要求。梁和桁架構件的變形有平面內的垂直變形和平面外的側向變形，因此要檢測兩個方向的平直度。

The allowable value of deviation shall meet the requirements of product standards. The deformation of beams and truss members includes vertical deformation in the plane and lateral deformation out of the plane, so it is necessary to detect the straightness in both directions.

柱的變形主要有柱身傾斜與撓曲。檢查時可先目測，發現有異常情況或疑點時，對梁、桁架可在構件支點間拉緊一根鐵絲或細線，然后測量各點的垂度與偏差；

The deformation of the column mainly includes the tilt and deflection of the column body. During inspection, visual inspection can be carried out first. In case of any abnormality or doubt, a wire or thin line can be tightened between the supporting points of the beam and truss, and then the verticality and deviation of each point can be measured;

對柱的傾斜可用經緯儀或鉛垂測量。柱撓曲可在構件支點間拉緊一根鐵絲或細線測量。

The tilt of the column can be measured with theodolite or plumb. The deflection of the column can be measured by tensioning a wire or thin wire between the supporting points of the component.

此外輕型鋼結構中所用的構件一般是由鋼廠批量生產，并需有合格證明，因此材料的強度及化學成分是有良好保證的。更多相關的內容就來我們網站http://hox8.com咨詢吧！

In addition, the components used in light steel structures are generally produced in batches by steel plants and need to have qualification certificates, so the strength and chemical composition of materials are well guaranteed. More relevant content will come to our website http://hox8.com Consult!